[صفحه اصلی ]   [Archive] [ English ]  
جستجو در پایگاه

جستجوی پیشرفته
..
نظرسنجی
مطالب کدام بخش سایت بیشتر مورد نیاز شماست؟
پرسش و پاسخ
جشنواره شهید هدایت
کلینیک تخصصی دندانپزشکی
مجله علمی
نمایشگاه کتاب
نمایشگاه مواد و تجهیزات دندانپزشکی
نیازمندیها
   
..
:: جلد 0 - ترمیمی ::
جلد 0 - ترمیمی صفحات 0-0 برگشت به فهرست نسخه ها
چکیده:   (1128 مشاهده)

 Clinical Relevance

  To obtain high repair bond strength on aged silorane composite, aluminum oxide sandblasting should be used as a surface treatment procedure. After aluminum oxide sandblasting, either silorane composite with the LS system adhesive or methacrylate composite with a methacrylate dental adhesive can be used.

 SUMMARY

  Objective: This laboratory study compared the repaired microtensile bond strengths of aged silorane resin composite using different surface treatments and either silorane or methacrylate resin composite.

 Methods: One hundred eight silorane resin composite blocks (Filtek LS) were fabricated and aged by thermocycling between 8°C and 48°C (5000 cycles). A control (solid resin composite) and four surface treatment groups (no treatment, acid treatment, aluminum oxide sandblasting, and diamond bur abrasion) were tested (N=12 blocks, 108 beams/group). Each treatment group was randomly divided in half and repaired with either silorane resin composite (LS adhesive) or methacrylate resin composite (Filtek Z250/Single Bond Plus). After 24 hours in 37°C distilled water, microtensile bond strength testing was performed using a non-trimming technique. Surface topography after surface treatment was analyzed using scanning electron microscopy (SEM). Failure mode was examined using optical microscopy (50×).

 Results: Weibull-distribution survival analysis revealed that aluminum oxide sandblasting followed by silorane or methacrylate resin composite and acid treatment with methacrylate resin composite provided insignificant differences from the control (p>0.05). All other groups were significantly lower than the control. Failure was primarily adhesive in all groups.

 Conclusion: Aluminum oxide sandblasting produced microtensile bond strength not different from the cohesive strength of silorane resin composite. After aluminum oxide sandblasting, aged silorane resin composite can be repaired with either silorane resin composite with LS system adhesive or methacrylate resin composite with methacrylate dental adhesive.


 Source: Operative Dentistry

 Full Text

     
نوع مطالعه: پژوهشي | موضوع مقاله: ترمیمی
دریافت: 1392/1/20 | پذیرش: 1394/9/25 | انتشار: 1394/9/25
ارسال نظر درباره این مقاله
نام کاربری یا پست الکترونیک شما:

CAPTCHA


XML   English Abstract   Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:




بازنشر اطلاعات
Creative Commons License این مقاله تحت شرایط Creative Commons Attribution-NonCommercial 4.0 International License قابل بازنشر است.
جلد 0 - ترمیمی برگشت به فهرست نسخه ها
جامعه اسلامی دندانپزشکان Islamic Dental Association of IRAN

کلیه حقوق سایت متعلق به جامعه اسلامی دندانپزشکان ایران است. تماس با ما

Persian site map - English site map - Created in 0.06 seconds with 37 queries by YEKTAWEB 4714