fa Comparison the Marginal and Internal Fit of Metal Copings Cast from Wax Patterns Fabricated by CAD/CAM and Conventional Wax up Techniques پروتزهای دندانی Prothtodontics پژوهشي Research <p> <strong>Statement of Problem:</strong> Metal-ceramic crowns are most commonly used as the complete coverage restorations in clinical daily use. Disadvantages of conventional hand-made wax-patterns introduce some alternative ways by means of CAD/CAM technologies.</p><p> <strong> Purpose</strong>: This study compares the marginal and internal fit of copings cast from CAD/CAM and conventional fabricated wax-patterns. <strong></strong></p><p> <strong>Materials and Method:</strong> Twenty-four standardized brass dies were prepared and randomly divided into 2 groups according to the wax-patterns fabrication method (CAD/CAM technique and conventional method) (n=12). All the wax-patterns were fabricated in a standard fashion by means of contour, thickness and internal relief (M1-M12: representative of CAD/CAM group, C1-C12: representative of conventional group). CAD/CAM milling machine (Cori TEC 340i imes-icore GmbH, Eiterfeld, Germany) was used to fabricate the CAD/CAM group wax-patterns. The copings cast from 24 wax-patterns were cemented to the corresponding dies. For all the coping-die assemblies cross-sectional technique was used to evaluate the marginal and internal fit at 15 points. The Student’s t- test was used for statistical analysis (α=0.05). <strong></strong></p><p> <strong>Results:</strong> The overall mean (SD) for absolute marginal discrepancy (AMD) was 254.46 (25.10) um for CAD/CAM group and 88.08(10.67) um for conventional group (control). The overall mean of internal gap total (IGT) was 110.77(5.92) um for CAD/CAM group and 76.90 (10.17) um for conventional group. The Student’s t-test revealed significant differences between 2 groups. Marginal and internal gaps were found to be significantly higher at all measured areas in CAD/CAM group than conventional group (p< 0.001). </p><p> <strong>Conclusion:</strong> Within limitations of this study, conventional method of wax-pattern fabrication produced copings with significantly better marginal and internal fit than CAD/CAM (machine-milled) technique. All the factors for 2 groups were standardized except wax pattern fabrication technique, therefore, only the conventional group results in copings with clinically acceptable margins of less than 120um. </p><hr><p></p><p> <strong>Source: </strong>Journal of Dentistry Shiraz University of Medical Sciences</p><p> <a href="http://dentjods.sums.ac.ir/index.php/JDSUMS/article/view/7" target="_blank"><font color="#0000ff">Full Text</font></a></p> 0 0 http://idai.ir/browse.php?a_code=A-10-32-2416&slc_lang=fa&sid=1 M. Vojdani 100319475328460011445 100319475328460011445 No Dept. of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran K. Torabi torabik@yahoo.com 100319475328460011446 100319475328460011446 Yes Dept. of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran E. Farjood 100319475328460011447 100319475328460011447 No Postgraduate Student, Dept. of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran AAR. Khaledi 100319475328460011448 100319475328460011448 No Postgraduate Student, Dept. of Prosthodontics, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran