[صفحه اصلی ]   [Archive] [ English ]  
جستجو در پایگاه

جستجوی پیشرفته
..
نظرسنجی
مطالب کدام بخش سایت بیشتر مورد نیاز شماست؟
پرسش و پاسخ
جشنواره شهید هدایت
کلینیک تخصصی دندانپزشکی
مجله علمی
نمایشگاه کتاب
نمایشگاه مواد و تجهیزات دندانپزشکی
نیازمندیها
   
..
:: جلد 0 - ترمیمی ::
جلد 0 - ترمیمی صفحات 0-0 برگشت به فهرست نسخه ها
Monomer-to-polymer conversion and micro-tensile bond strength to dentine of experimental and commercial adhesives containing diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide or a camphorquinone/amine photo-initiator system
چکیده:   (2928 مشاهده)

 Objectives

  To compare the degree of conversion (DC) of adhesives initiated by diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide (TPO) or a camphorquinone/tertiary amine system (CQ/Amine) as well as their ‘immediate’ micro-tensile bond strength (μTBS) to bur-cut dentine.

 Methods

  DC of Scotchbond Universal (‘SBU’ 3M ESPE), its experimental counterpart containing TPO as photo-initiator system, an experimental G-aenial Bond (‘Ga-B’ GC) adhesive formulation, and an experimental LUB-102 adhesive formulation (‘LUB’, Kuraray Noritake), containing as photo-initiatior system either 2wt% CQ along with 2wt% tertiary amine (‘SBU_CQ/Amine’ ‘Ga-B_CQ/Amine’ ‘LUB_CQ/Amine’), or 2wt% TPO (‘SBU_TPO’ ‘Ga-B_TPO’ ‘LUB_TPO’), was determined using Fourier-transform infrared spectroscopy (FTIR), after being cured with a dual-wavelength light-curing unit (bluephase 20i, Ivoclar Vivadent). The same adhesive formulations were applied to bur-cut mid-coronal dentine of intact human molars, and subjected to a μTBS test after 1-week water storage. Besides being applied following a self-etch (SE) application mode, the adhesive formulations SBU_CQ/Amine and SBU_TPO were also applied following an etch-and-rinse (E&R) mode, this both for DS and μTBS measurement.

 Results

  No significant difference in DC was found for any of the adhesive formulations, except for SBU_CQ/Amine_SE and SBU_TPO_SE. For both SBU formulations, a significantly higher DC was reached for the E&R than the SE approach. Regarding μTBS, no significant differences were recorded, except for the significantly higher μTBS measured for SBU_CQ/Amine_E&R and SBU_TPO_E&R.

 Conclusions

 In self-etch adhesives, the photo-initiator TPO may be used instead of CQ/Amine. The curing and ‘immediate’ bonding efficiency depended on the application protocol (E&R versus SE), but not on the photo-initiator system.

  Clinical significance

 The photo-initiator TPO may be used in self-etch adhesives instead of CQ/Amine with similar curing and ‘immediate’ bonding efficiency.


 Source: Journal of Dentistry

 Full Text

واژه‌های کلیدی: Adhesive، Degree of conversion، Bond strength، Dentine، TPO، FTIR
     
نوع مطالعه: پژوهشي | موضوع مقاله: ترمیمی
دریافت: 1392/7/22 | پذیرش: 1394/9/25 | انتشار: 1394/9/25
ارسال نظر درباره این مقاله
نام کاربری یا پست الکترونیک شما:

CAPTCHA


XML     Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:


Monomer-to-polymer conversion and micro-tensile bond strength to dentine of experimental and commercial adhesives containing diphenyl(2,4,6-trimethylbenzoyl)phosphine oxide or a camphorquinone/amine photo-initiator system. 1. 1390;

URL: http://idai.ir/article-1-2231-fa.html



بازنشر اطلاعات
Creative Commons License این مقاله تحت شرایط Creative Commons Attribution-NonCommercial 4.0 International License قابل بازنشر است.
جلد 0 - ترمیمی برگشت به فهرست نسخه ها
جامعه اسلامی دندانپزشکان Islamic Dental Association of IRAN

کلیه حقوق سایت متعلق به جامعه اسلامی دندانپزشکان ایران است. تماس با ما

Persian site map - English site map - Created in 0.04 seconds with 35 queries by YEKTAWEB 4710